## Transactions of the North-East Coast Institution of Engineers and Shipbuilders ..., Band 8North East Coast Institutiton of Engineers and Shipbuilders., 1892 "Catalogue of papers read before the ... institution, vols. I-XVII, 1884-1901", in v. 17, p. 261-265. |

### Was andere dazu sagen - Rezension schreiben

Es wurden keine Rezensionen gefunden.

### Andere Ausgaben - Alle anzeigen

### Häufige Begriffe und Wortgruppen

acid arrangement bar keel Barrow-in-Furness beam bilge water Board of Trade boiler bottom bulkhead bush c/o Messrs capacity careening cargo carried cement centre classification societies coal condenser considerable Construction Council dead-weight deck discussion displacement draught Draughtsman engine room Engineer Apprentice Engineers and Shipbuilders fatty acid feed-water feet filter fitted flange frames freeboard Gateshead-on-Tyne inches Indian Railways iron James Jarrow-on-Tyne John length liners Lloyd's Register loaded Macoll matter meeting metacentric height mineral oil Naval Newcastle-on-Tyne Nichol NORTH-EAST COAST INSTITUTION ordinary pipes practical President propeller proposed pumps riveting Road rule screw Secretary sections shaft Ships and Steamers shown side Simpson's rule South Shields space speed stability steam steel stern tube stern-wheel Street Sunderland Tenedos Terrace thought tion tonnage tonnage measurement tons Tyne valves vessel Wailes Walker-on-Tyne Wallsend-on-Tyne weight well-decker West Hartlepool William writer

### Beliebte Passagen

Seite 118 - ... area (except the first and last) by two ; add these products together, and to the sum add the first and last if they yield anything; multiply the quantity thus obtained by one-third of the common interval between the areas, and the product will be the cubical contents of the space under the tonnage deck...

Seite 118 - ... feet, divide each depth into four equal parts; then measure the inside horizontal breadth, at each of the three points of division, and also at the upper and lower points of the depth, extending each measurement to the average thickness of that part of the ceiling which is between the points of measurement; number these breadths from above, numbering the upper breadth one, and so on down to the lowest breadth; multiply the second and fourth by four, and...

Seite 118 - Measure the depth at each point of division from a point at a distance of one-third of the round of the beam below such deck; or, in case of a break, below a line stretched in continuation thereof, to the upper side of the floor timber...

Seite xlvi - The Council may refuse to continue to receive the subscriptions of any person who shall have wilfully acted in contravention of the regulations of the Institution, or who shall in the opinion of the Council have been guilty of such conduct as shall have rendered him unfit to continue to belong to the Institution...

Seite 117 - ... of the round of the beam; divide the length so taken into the number of equal parts required by the following table, according to the class in such table to which the ship belongs: — TABLE Class 1.

Seite 118 - ... ship, at each point of division of the length, as follows: — Measure the depth at each point of division, from a point at a distance of one-third of the round of the beam below such...

Seite 119 - ... points of division, and also at the upper and lower points of the depth, number them from above as before ; multiply the second, fourth, and sixth by four, and the third and fifth by two ; add these products together, and to the sum add the first breadth and the seventh ; multiply the quantity thus obtained by one-third of the common interval between the breadths, and the product shall be deemed the transverse area.

Seite 117 - No. 1 being at the extreme limit of the length at the bow, and the last No. at the extreme limit of the length at the stern ; then, whether the length be divided according...

Seite 117 - ... thus obtained by one-third of the common interval between the areas, and the product will be the cubical contents of the space under the tonnage deck; divide this product by...

Seite 115 - ... in one-third of the round of the beam; divide the length so taken into the number of equal parts required by the following table, according to the class in such table to which the vessel belongs : Class one.